Published Written and reviewed by 秋和PC
What to Check Before Building in a Pillarless or Showcase Case
Problems that come up with pillarless cases you can see into through the glass, and with builds full of parts that have screens: graphics card thickness, cooler tube length, the number of USB devices, and control software, from our on-site builds.
"Pillarless" cases with no pillar at the front corner, and showcase cases designed to put the inside on display, are popular because they look great. More and more people are also adding pump heads with screens, LCD fans and small secondary monitors.
But builds like these are more prone to parts getting in each other's way, and to having too many USB devices. Based on real examples from our on-site builds, here's what to check before you start.
1. Graphics card thickness and cable direction
In a showcase case, fitting bottom fans or using certain kinds of motherboard can shrink the space available for the graphics card.
On a build in Arai-Yakushimae using an ASUS AP202 case with a Ryzen 7 9800X3D and an RTX 5080, we ran into these limits:
- With bottom fans fitted and a motherboard with its connectors on the back, the graphics card could be no thicker than two slots
- Routing the card's power cable downwards would hit the fans, so we routed it from the top
Besides the maximum graphics card length in the case specs, check its thickness (in slots) and where its power connector is. A card with the power connector at the end rather than on the side can be easier to cable.
Motherboards with connectors on the back
Motherboards that put their cable connectors on the back side make the wiring almost invisible from the front. But they need a compatible case, and, as in the example above, they can narrow your choice of other parts.
2. Liquid cooler tube length
Where you mount an all-in-one liquid cooler's radiator determines how long its tubes need to be.
In the AP202 build, the tubes on the ROG RYUJIN IV had little slack, and we had to adjust things so they weren't under strain. In this case, a cooler with longer tubes makes assembly easier.
Leaving the tubes sharply bent puts strain on the pump and the tube fittings. Check the radiator position and tube length against the case specs in advance.
3. Count your USB devices
Parts with screens often use the motherboard's internal USB headers for display or control.
A pillarless all-Lian Li build we assembled in Mizonokuchi had eight wireless LCD fans, a pump head with a screen, an 8.8-inch secondary monitor and a graphics card with a screen, seven USB devices in total.
Each internal USB 2.0 header on a motherboard can connect two devices, but most boards have only one or two of these headers. With many screen-equipped parts or fan controllers, you'll need an internal USB hub. Count your devices and headers before you buy.
4. Expect more control software
Combining screen-equipped parts and lighting from different makers means each one needs its own control software.
In the Mizonokuchi build, we set up software from ASUS, Colorful, TRYX, Lian Li and Turing Smart Screen. For a Lian Li ARGB cable and LCD fan connections that weren't working properly, we checked each pair one at a time to find the cause. The job ran late into the night, but we handed over the PC with every screen and every light working.
- Two programs trying to control the same device can make the lighting display incorrectly
- With many screen-equipped devices, it can take a while after boot for all the drivers to be ready
- To keep the number of programs down, stick to one brand for fans and lighting
5. Balancing cooling and looks
Many pillarless cases take in air from the side or bottom, so fan placement affects how well the PC cools.
In a white ROG Hyperion build in Ichikawa (Motoyawata), we arranged four Lian Li 140 mm wireless fans as three intakes and one exhaust. Choosing fan directions purely for looks can trap heat inside the case, so also think about the balance of intake and exhaust.
6. Allow plenty of time
Builds with many parts, or many screen-equipped parts, take longer than a typical build. High-end builds with lots of parts have taken us anywhere from half a day to nearly a full day.
For finishing the cabling, see also our cable management tips.
What to tell us before booking
- The models of the case, motherboard, graphics card and liquid cooler
- The number of screen-equipped parts, fans and controllers
- What you'd like it to look like, such as fan directions and lighting
With the model numbers, we can check for clearance problems and missing USB headers in advance, and bring any hubs you'll need.
Related service cases
- On-site ASUS AP202 build in Arai-yakushimaeAn on-site ASUS AP202 build in Arai-yakushimae, balancing component clearance, cooling, and presentation.
- Lian Li panoramic build with screen and lighting setup in MizonokuchiAn on-site Lian Li panoramic build in Mizonokuchi, Kawasaki, including setup of multiple screens and lighting.
- On-site white NZXT × ROG panoramic build in Seiseki-SakuragaokaAn on-site white build in Seiseki-Sakuragaoka with an NZXT case, ROG parts and Lian Li fans.
- On-site white ROG Hyperion build in Motoyawata, IchikawaAn on-site all-white high-end build around an ROG Hyperion White Edition case in Motoyawata, Ichikawa.