Published Written and reviewed by 秋和PC
Replacing or Upgrading a Power Supply: Wattage, Connectors and Size
When you replace a power supply because it failed or because you are upgrading the graphics card: how much wattage you need, what the 12V-2x6 connector is, checking that it fits the case, and the cable mistake to avoid.
The power supply unit (PSU) feeds power to every part of the PC. Besides replacing failed units, we often get requests to replace the PSU as part of a graphics card upgrade.
Choosing the wrong PSU can mean a PC that won't start, shuts down under load, or in the worst case damages other parts. Here is what to check before replacing one.
1. Decide whether it needs replacing
Consider replacing the power supply when:
- It has failed: nothing happens when you press the power button, or the PC shuts off only under heavy load such as gaming
- It doesn't have enough wattage: you are moving to a graphics card or CPU that draws more power
- It lacks the right connectors: the new graphics card needs a power connector your current PSU doesn't have
For working out whether the PSU has failed, see our checklist for a PC that won't start.
2. How much wattage
Check the graphics card's recommended PSU
The most reliable reference is the recommended power supply published by the graphics card maker. For example, NVIDIA recommends a 1000 W system power supply for the RTX 5090 and 850 W for the RTX 5080. For factory-overclocked models, the board partner may recommend more.
Why to leave headroom
We recommend leaving some margin rather than buying exactly the recommended figure:
- Graphics cards can briefly draw far more than their rated power
- Power supplies tend to run more efficiently at around half their capacity
- It leaves room to add or upgrade parts later
On the other hand, an oversized unit costs more and is physically larger. Adding up the CPU and graphics card power draw, then adding a margin, is a practical starting point.
The limit of a Japanese household outlet
A standard household outlet in Japan is 100 V, 15 A, which puts the limit for one circuit at roughly 1500 W. If you are considering a PSU over 1500 W, or will run other appliances on the same circuit, read our notes on high-wattage power supplies first.
3. Connector types
12V-2x6 (12VHPWR)
Most recent high-end graphics cards use a 16-pin power connector called 12V-2x6 (the earlier version was called 12VHPWR). Power supplies that support ATX 3.1 usually include a cable for it.
- A native cable from the PSU is more reassuring than an adapter
- Push the connector all the way in. A partially inserted connector can overheat at the contacts
- Avoid bending the cable sharply right at the connector, especially in a narrow case
Other connectors
Also check that you have enough of the 24-pin motherboard connector, the 8-pin CPU connector (some high-end motherboards need two), and SATA connectors for drives and fans.
4. Will it fit the case?
Besides the common ATX size, power supplies come in smaller formats such as SFX for compact cases. Even among ATX units, length varies a lot between products, and higher-wattage units tend to be longer.
Compare the "maximum PSU length" in your case's specifications with the length of the new unit. Modular cable plugs need extra room as well, so avoid a unit that only just fits.
5. Don't reuse the old PSU's cables
This is the most important point when replacing a power supply.
On modular power supplies, the pin layout can differ between brands and models even when the plug on the PSU side looks the same. Plugging the old unit's cables into a new PSU can destroy the motherboard, graphics card or drives.
The rule is to replace every cable with the ones that come with the new PSU.
When we replaced the power supply in a high-end PC on one job, we swapped all the cables for new ones. Since the wiring had to be redone anyway, we also tidied up cabling that had been rough to begin with. A PSU swap is a good opportunity to rework the cable management.
6. Overview of the replacement steps
- Shut down the PC and unplug the power cord
- Turn off the switch on the back of the PSU and wait a little
- Disconnect the power cables from each part, and photograph the cable routing
- Remove the old PSU from the case
- Install the new PSU and connect it using its own cables
- Confirm the PC starts, then check that it stays stable under heavy load such as gaming
Never open the power supply itself. The capacitors inside can hold a high voltage even after the power is off.
When replacing other parts at the same time
When moving to a more powerful graphics card, check the PSU's wattage and connectors. When changing the CPU, check the socket type and whether the motherboard's BIOS supports the new CPU.
On one job, a customer brought their PC to us and we replaced the power supply, CPU and graphics card together, and they took it home the same day. Replacing related parts at once lets you handle the work and the compatibility checks in one go.
What helps if you know it in advance
- The model and wattage of your current PSU (printed on the label on its side)
- The case model
- The model of the graphics card or CPU you plan to install
With this, we can confirm a PSU with the right wattage and size before starting work.
Related service cases
- On-site ROG desktop power-supply replacement in KachidokiAn on-site power-supply replacement for an ASUS ROG desktop in Kachidoki, with connector, cabling, and startup checks.
- Desktop power supply, CPU, and GPU upgrade in TokyoA same-day power supply, CPU, and graphics card upgrade for a desktop PC.
- On-site gaming GPU error diagnosis in KachidokiOn-site diagnosis of a gaming GPU error in Kachidoki, checking each likely cause before assuming the graphics card had failed.