Published Updated Written and reviewed by 秋和PC
PC Won't Start or Shows No Display: A Troubleshooting Checklist
No power at all, fans spin but no picture, or Windows won't load. The causes we see most often on on-site repair jobs, and the order in which you can check them yourself.
"I press the power button and nothing happens" is one of the most common requests we get for on-site repair. But a PC that "won't start" can have many causes: the power supply, memory, CPU, graphics card, a USB device, or even drive encryption.
First, decide which of these three symptoms matches yours. That alone narrows the list of likely causes a lot.
- No response at all (no fans, no lights)
- Fans and lights come on, but there is no picture
- The manufacturer logo appears, but Windows won't load
1. No response at all
Check these first
- Is the power cable pushed all the way in at both the wall and the PC?
- Is the switch on the back of the power supply set to "I" (on)?
- Does the same thing happen when you plug directly into a wall outlet instead of a power strip?
A failed power supply
If all of that is fine, the most common cause is a failed power supply unit (PSU). On real jobs we have repeatedly seen PCs that worked the day before and then showed no sign of life at all, and started immediately once we fitted a working PSU. We have also seen the same PSU model fail again and again; the PSU is one of the parts most prone to wear and failure.
If you replace it yourself, never reuse modular PSU cables with a different unit. Even when the connectors look the same, the pin layout can differ between brands and models, and mixing them can destroy components. Even for the same PSU model, confirm compatibility between the specific PSU and cables using the manufacturer's documentation. If compatibility cannot be confirmed, use the cables supplied with the replacement PSU.
"USB device over current status detected"
Sometimes the PC powers on, shows "USB device over current status detected" and shuts down a few seconds later. The cause is usually either a short circuit in a USB device or cable, or a motherboard fault.
In one case we brought a replacement motherboard just in case, but found that the internal cable for the case's front Type-C port had shorted. Simply unplugging that cable from the motherboard let the PC boot normally.
If you see this message, unplug all USB devices first. If it still appears, suspect the front-panel USB cables.
2. Fans spin, but there is no picture
Check the motherboard LEDs
Many modern motherboards have debug LEDs (CPU / DRAM / VGA / BOOT) that show where the power-on self-test is stuck. An LED that stays lit is a strong clue.
- DRAM stays lit: the memory is not being detected. Remove the memory and reseat it until it clicks. We have had PCs start after nothing more than reseating the memory. On small ITX boards, memory compatibility can also cause unstable detection.
- DRAM stays lit even after reseating: the problem may be the CPU rather than the memory. In one case the PC started with a different CPU, while the customer's CPU never passed the memory check no matter what we tried, so we diagnosed a faulty CPU.
- VGA stays lit: there is a problem detecting the graphics card.
Isolating the graphics card
If a dedicated graphics card is installed, normally connect the monitor to the graphics card's video output first. Without a dedicated card, the motherboard's video output requires a CPU with integrated graphics and a supported motherboard video connector. Check the device manuals.
If it still doesn't work and your CPU has integrated graphics, remove the graphics card and try the motherboard's video output. In one case, the PC showed no picture even on integrated graphics while the faulty card was installed, and our test PC worked fine, so we concluded the graphics card had failed.
3. Windows won't load
Asked for a BitLocker recovery key
At startup you may see a blue screen asking for a BitLocker recovery key. BitLocker encrypts the drive, and without the recovery key the data cannot be read.
- For a personal PC, the key is often saved on the "Recovery keys" page of your Microsoft account. Check it from another device first.
- For a company PC, ask your administrator or the previous user whether they kept the key.
We have seen a PC that a former employee had used, where neither the password nor the recovery key was known, and the only option was to reinstall and lose the data. For company PCs, we strongly recommend handing over the account and recovery key before the person in charge changes.
It starts but stops on a blue screen
If you get blue screens after reinstalling the OS, the cause has to be narrowed down: drivers, storage, memory and so on. Take a photo of the error code with your phone; it helps a lot in finding the cause.
Things you should not do yourself
- Opening the power supply: capacitors inside can hold a high voltage even after the power is off. It is dangerous.
- Plugging or unplugging parts while powered: always unplug the power cable and wait several tens of seconds first.
- Formatting a drive that holds important data: if you format while BitLocker is locked or the PC won't boot, the data cannot be recovered.
What to tell us before booking a repair
- The PC model, or the parts list if it is a custom build
- When the problem started and what changed just before (a Windows update, moving the PC, adding parts, etc.)
- The color of the motherboard LEDs, or a photo of any message on screen
If we know this in advance, we can bring a replacement PSU and test parts, which makes it much more likely we can solve the problem in a single visit.
Related service cases
- White HYTE PC that would not power on in ShibuyaA white HYTE PC in Shibuya that seemed not to power on started normally once the steps were confirmed, followed by initial system setup.
- On-site gaming GPU error diagnosis in KachidokiOn-site diagnosis of a gaming GPU error in Kachidoki, checking each likely cause before assuming the graphics card had failed.
- Laptop blue-screen service after Windows reinstallation in TokyoWe checked a post-reinstallation blue screen step by step and restored a testable system environment while protecting necessary data.
- BitLocker unlock failure with data kept and system repaired in MachiyaA PC in Machiya that BitLocker would not unlock was decrypted, then Windows was reinstalled without losing data.