Published Written and reviewed by 秋和PC
PC Cable Management Tips: From Planning the Build to Handling Stiff Cables
Want the cables you see through the glass to look clean? How to use the space behind the motherboard, the order to route cables in, ways to cut down fan and lighting wiring, and what to watch for with white parts, from our on-site builds.
With glass-panel cases now the norm, more people ask us to make the cabling look good too. Some have built the PC themselves but aren't happy with the cables, and ask us to redo just the wiring.
Cable management isn't only about looks. Tidy cables are less likely to block airflow, collect less dust, and make it easier to swap parts later.
1. Plan the cable routes before building
The biggest secret to clean cabling is planning before you assemble.
- Check where each motherboard connector is (24-pin, CPU 8-pin, front panel, USB, fans)
- Decide which hole (grommet) in the case each cable will pass through
- If there are many drives or fans, decide where they'll go and where their cables will be gathered
For high-end builds with lots of parts, it's worth spending time just on planning the layout and cabling.
2. The order to route cables in
In a small case or with a large cooler, getting the order wrong can leave you unable to reach things.
- The CPU power cable connects at the top edge of the motherboard, so route it before fitting a large radiator or air cooler
- In some cases it's easier to pass the top-edge cables through their holes before screwing the motherboard in
- Installing the graphics card near the end makes it easier to reach the connectors along the bottom (front panel, USB, fans)
3. Use the space behind the motherboard
Behind the motherboard there's space for running cables. How much space there is, and how cables are held in place, varies a lot between cases.
The NZXT case we built in for a customer in Seiseki-Sakuragaoka had a generous amount of space behind the motherboard, and the cables were almost invisible through the front glass. How clean the cabling looks depends a lot on the case you choose. If cabling matters to you, include the rear cable space and cable-tie points in your case criteria.
When bundling cables, we recommend hook-and-loop (Velcro) straps over zip ties. You can take them off without cutting when you add or replace cables later.
4. Cut down fan and lighting cables
In builds with lots of fans, fan and lighting cables are the biggest source of clutter.
- Daisy-chain fans: choose fans that link together so several run off one cable
- Wireless fans: these cut the number of cables dramatically
- Fan hubs and ARGB controllers: use them when the motherboard runs out of headers, and gather cables at the hub
Fans and lighting connect in different ways depending on the product, so it's important to check before buying. See also common pitfalls when building a PC.
5. Handling stiff power cables
Some power supplies come with stiff cables that won't bend the way you want.
On a job near Shinjuku-gyoemmae, the power supply's cables were on the stiff side, so we had to be careful about how we bent them. Forcing a cable puts strain on the connector, so choose routes that suit how stiff the cable is.
- If looks matter, you can use soft sleeved cables or extension cables
- But never reuse modular cables from a different power supply. The pin layout differs and can destroy your parts (see our power supply replacement guide)
- Don't bend the graphics card's 16-pin cable sharply right at the connector
6. Building with white parts
An all-white build looks unified, but black cables stand out.
- Choose a power supply that comes with white cables, or get white cables separately
- Reduce the number of visible cables and keep their routes parallel
7. Checks after you finish
- Are any cables touching fan blades?
- Is any cable under strain, especially at the base of a connector?
- Is anything pinched when you close the side panel?
Don't forget the cables around the desk
Tidying the cables around your desk, not just inside the PC, also means less dust and easier cleaning. On regular maintenance visits, we've combined cleaning and recabling inside the PC with fitting a monitor arm and tidying the cables around the desk.
Asking us to redo your cabling
We can redo just the cabling on a PC you built yourself. On a job in Hasune, we replaced a failed side fan and added a drive, and rerouted the cabling throughout the whole case at the same time.
If you send us the case model and a photo of the inside when you book, it's easier for us to estimate how long the work will take.
Related service cases
- Cable management and fan replacement for a black ASUS PC in HasuneRe-cabling a customer's self-built black ASUS PC in Hasune, with a fan replacement and an added drive.
- On-site white NZXT × ROG panoramic build in Seiseki-SakuragaokaAn on-site white build in Seiseki-Sakuragaoka with an NZXT case, ROG parts and Lian Li fans.
- Finishing a white RTX 5080 build near Shinjuku-gyoemmaeTaking over a partly built white RTX 5080 PC near Shinjuku-gyoemmae and finishing the assembly and cabling.
- All-ASUS ROG Helios build and cable management in KameidoAn on-site all-ASUS build in a ROG Strix Helios case in Kameido, with careful cable management.
- On-site desktop cleaning and cable management in TokyoOn-site desktop cleaning with desk cable organization to improve airflow and make future maintenance clearer.